November Slack-R Headset Angle Kit 1.6°

What does installing a Slack-R do to your bikes geometry?
Click HERE to take a deeper look.

Want more customization?
Add additional parts to your Slack-R Kit to fine tune your HTA and test the extremes with one of our angle sets. Individual parts located HERE.

IS41/IS52 will fit a number of bikes from manufacturers such as Yeti, Santa Cruz, and Trek (eliminates the need for a Knock Block in most cases). Cube is an exception as they use a deeper upper bearing seat and the Slack-R IS41 will not sit properly in the Cube frames.

IS42/IS52 will fit many bikes from Cannondale, Norco, Marin, Orbea, GT, Revel, Scott and many more including some Specialized with a standard depth IS42/IS52 headset. Standard bearing seat depth is 3mm

IS42S/IS52 will fit Specialized bikes that have the 6.8mm deep upper bearing seat. (some Specialized bearings sit deeper than the standard IS42 geometry so they require their own specific top cup to insure proper fitment)

Headset types do vary across the same manufacturer, make sure you are sure what kind of headset you have. (IS/EC/ZS or hybrids of these)

Some IS bearing seats in the frames have a smaller bearing seat inside diameter than others so in some cases a bit of sanding will be required to fit in the 34.5mm upper sleeve and 44.5mm lower sleeve. In most cases the frame allow the kits to drop right in but in some cases opening up the upper and/or lower bearing seat inside diameter(s) will be required so double check your frame clearance prior to ordering if unsure.

Contact support@9point8.ca if you are unsure about your application prior to ordering.

Does your bike have a Trek Knock Block headset?
The Stop Chip must be removed from all Trek Knock Block headsets before installing a Slack-R. Read more here.

For your HTL and desired Angle Change, look up the Kit you need, and the Upper Cup, Tensioner, and Lower Cup part numbers you need.

Slack-R IS Kit Reference Chart

Kit	HTL (Target middle-of-range)	Nominal Angle (Deg.)	Upper Cup	Upper Cup Length (mm)	Lower Cup	Lower Cup Length (mm)	Tensioner	Tensioner Length (mm)	Added Stack (mm)
Alpha IS41	90-98	1.5	0000-1343	22-26	0000-1349	25-29	0000-1345	43	20
Alpha IS42	90-98	1.5	0000-1371	22-26	0000-1349	25-29	0000-1345	43	20
Alpha IS42S	90-98	1.5	0000-1373	22-26	0000-1349	25-29	0000-1345	43	25
Bravo IS41	100-108	1.4	0000-1343	22-26	0000-1349	25-29	0000-1346	53	20
Bravo IS42	100-108	1.4	0000-1371	22-26	0000-1349	25-29	0000-1346	53	20
Bravo IS42S	100-108	1.4	0000-1373	22-26	0000-1349	25-29	0000-1346	53	25
Charlie IS41	110-118	1.3	0000-1343	22-26	0000-1349	25-29	0000-1347	63	20
Charlie IS42	110-118	1.3	0000-1371	22-26	0000-1349	25-29	0000-1347	63	20
Charlie IS42S	110-118	1.3	0000-1373	22-26	0000-1349	25-29	0000-1347	63	25
Delta IS41	120-128	1.2	0000-1343	22-26	0000-1349	25-29	0000-1348	73	20
Delta IS42	120-128	1.2	0000-1371	22-26	0000-1349	25-29	0000-1348	73	20
Delta IS42S	120-128	1.2	0000-1373	22-26	0000-1349	25-29	0000-1348	73	25
Echo IS41	97-105	1.7	0000-1343	22-26	0000-1350	32-36	0000-1345	43	20
Echo IS42	97-105	1.7	0000-1371	22-26	0000-1350	32-36	0000-1345	43	20
Echo IS42S	97-105	1.7	0000-1373	22-26	0000-1350	32-36	0000-1345	43	25
Foxtrot IS41	107-115	1.6	0000-1343	22-26	0000-1350	32-36	0000-1346	53	20
Foxtrot IS42	107-115	1.6	0000-1371	22-26	0000-1350	32-36	0000-1346	53	20
Foxtrot IS42S	107-115	1.6	0000-1373	22-26	0000-1350	32-36	0000-1346	53	25
Golf IS41	117-125	1.5	0000-1343	22-26	0000-1350	32-36	0000-1347	63	20
Golf IS42	117-125	1.5	0000-1371	22-26	0000-1350	32-36	0000-1347	63	20
Golf IS42S	117-125	1.5	0000-1373	22-26	0000-1350	32-36	0000-1347	63	25
Hotel IS41	127-135	1.4	0000-1343	22-26	0000-1350	32-36	0000-1348	73	20
Hotel IS42	127-135	1.4	0000-1371	22-26	0000-1350	32-36	0000-1348	73	20
Hotel IS42S	127-135	1.4	0000-1373	22-26	0000-1350	32-36	0000-1348	73	25
India IS41	110-118	1.5	0000-1344	42-46	0000-1349	25-29	0000-1345	43	20
India IS42	110-118	1.5	0000-1372	42-46	0000-1349	25-29	0000-1345	43	20
India IS42S	110-118	1.5	0000-1374	42-46	0000-1349	25-29	0000-1345	43	25
Juliet IS41	120-128	1.4	0000-1344	42-46	0000-1349	25-29	0000-1346	53	20
Juliet IS42	120-128	1.4	0000-1372	42-46	0000-1349	25-29	0000-1346	53	20
Juliet IS42S	120-128	1.4	0000-1374	42-46	0000-1349	25-29	0000-1346	53	25
Kilo IS41	130-138	1.4	0000-1344	42-46	0000-1349	25-29	0000-1347	63	20
Kilo IS42	130-138	1.4	0000-1372	42-46	0000-1349	25-29	0000-1347	63	20
Kilo IS42S	130-138	1.4	0000-1374	42-46	0000-1349	25-29	0000-1347	63	25
Lima IS41	140-148	1.3	0000-1344	42-46	0000-1349	25-29	0000-1348	73	20
Lima IS42	140-148	1.3	0000-1372	42-46	0000-1349	25-29	0000-1348	73	20
Lima IS42S	140-148	1.3	0000-1374	42-46	0000-1349	25-29	0000-1348	73	25
Mike IS41	117-125	1.7	0000-1344	42-46	0000-1350	32-36	0000-1345	43	20
Mike IS42	117-125	1.7	0000-1372	42-46	0000-1350	32-36	0000-1345	43	20
Mike IS42S	117-125	1.7	0000-1374	42-46	0000-1350	32-36	0000-1345	43	25
November IS41	127-135	1.6	0000-1344	42-46	0000-1350	32-36	0000-1346	53	20
November IS42	127-135	1.6	0000-1372	42-46	0000-1350	32-36	0000-1346	53	20
November IS42S	127-135	1.6	0000-1374	42-46	0000-1350	32-36	0000-1346	53	25
Oscar IS41	137-145	1.5	0000-1344	42-46	0000-1350	32-36	0000-1347	63	20
Oscar IS42	137-145	1.5	0000-1372	42-46	0000-1350	32-36	0000-1347	63	20
Oscar IS42S	137-145	1.5	0000-1374	42-46	0000-1350	32-36	0000-1347	63	25
Papa IS41	147-155	1.5	0000-1344	42-46	0000-1350	32-36	0000-1348	73	20
Papa IS42	147-155	1.5	0000-1372	42-46	0000-1350	32-36	0000-1348	73	20
Papa IS42S	147-155	1.5	0000-1374	42-46	0000-1350	32-36	0000-1348	73	25

Click on the image, or click here to download the Slack-R Instructions PDF

Okay, it says 1.5 degrees, but what does that mean installed on the bike?

Good question! We know some of you like to geek out on the geometry numbers, and we’d like everyone who buys a Slack-R to understand how it changes the geometry of their bike. It is a simple product, but the effect on the geometry is really complicated to work out! It varies according to your frame’s geometry, including frame size. We’ll use an example to illustrate. The bike we’ve chosen is a Santa Cruz Tallboy 3 in size Large. This is a great candidate for a Slack-R – it uses an IS headset, and while it is a well-regarded, capable bike, with a 68° head tube angle we can see a lot of riders wanting to make it just a touch slacker, just like Santa Cruz did with the latest Tallboy! The size Large Tallboy 3 has a 100mm head tube length – punching that into our calculator, we actually have two Slack-R kits available, the “Bravo” kit which lists a 1.4 head tube angle delta, and the “Echo” kit which lists 1.8 degrees. Those delta numbers tell you what the angle will be between the head tube of your frame and your fork steerer tube with the Slack-R installed, but because the Slack-R also adds some stack height due to the bearing cups, and because slackening the head tube angle actually lowers the front end of your bike, this doesn’t tell you exactly what the end result is. We’ve picked the Bravo kit for our example bike, and the resulting geometry on the Tallboy is shown in Figure 1: Santa Cruz Tallboy Example. Despite only a 1.4° delta between the head tube and the fork steerer tube, the overall change is actually 1.7°! Generally speaking that’s what we’d expect to see on most bikes – a slightly slacker head tube angle than the listed delta, a very small change in bottom bracket height, a slight increase in stack, a slight decrease in reach, and a noticeable increase in wheelbase.

2016-2019 Santa Cruz Tallboy (L)
29x2.3 Tires, Fox 34 120mm 29er Fork (527mm A2C)

 

Hold up, this changes my reach and stack too?

Yes it does! Since Slack-R effectively adds external upper and lower bearing cups, it raises the front end of your bike by the external height of the lower cup (about 10mm), and the upper cup adds about another 10mm to the stack measurement. Luckily, as you slacken the head tube angle, the front end of your bike drops as the fork kicks forward, and this effect balances out to a large degree the extra height due to the lower cup, which you can also see by the small change in bottom bracket height. On the top side, you still have the upper cup height to deal with, but if you’re running more than about a 10mm spacer below your stem, you can simply remove spacer(s) to get your bar height back right where it was. Keep in mind, because we’re adding stack height, you will need to remove spacers anyway – make sure your fork steerer is long enough! The change in reach is more subtle. Part of the reach change is based on the delta in head tube angle (picture the upper cup offset rearward), and part is related to the change in height of the front end. If you correct your stack height by removing spacers, you’ll also minimize the change in reach. Our example Tallboy shows an increase in stack of 9mm and a decrease in reach of 6mm, but removing a 10mm spacer would result in negligible in stack, and bring the change in (effective) reach down to about 3mm.

What if I want a steeper head tube angle? Do you make a Steep-R?

Yes we do! Actually, you can just run a Slack-R “backwards” with the alignment marks at the front of the bike. This will steepen the head tube angle, however, the effects aren’t quite what you might expect. We got a bit of a “bonus” in the change of the head tube angle on our example Tallboy with the Slack-R installed in the conventional orientation, but the same factors compound in the opposite way when you install it backwards. This basically all comes down to the added height of the cups compounded by the steeper angle raising the front end. Looking again at our Tallboy with the Bravo kit, we’d end up only making the head tube angle 0.5° steeper, and we add significantly to the stack and bottom bracket height, along with a more significant reduction in reach. Again assuming you have enough spacers under your stem, you may be able to compensate for the stack and reach changes, but short of changing your fork or reducing the travel, you’re stuck with the increase in bottom bracket height. While many riders will buy the Slack-R to slacken their head tube angle and be happy with it without ever reading any of these details, we view using it as a “Steep-R” as a niche application where riders may even be primarily interested in changing aspects of their geometry other than head tube angle.

Okay, now I’m just more confused?

If you’re not sure if Slack-R is right for you, or you want to understand exactly what the effect will be on your bike, we can help! Contact Customer Service by emailing service@9point8.ca.

ONLY COMPATIBLE WITH IS HEADSETS. (IS41 or IS42 upper bearing and IS52 lower bearing only.)